VERY GOOD SOUTH BEND LATHE. 10” SWING, 24 BETWEEN CENTERS, 3 1/2′ BED LENGTH ON CABINET. VINTAGE: METAL LABEL “THIS MACHINE CONFORMS TO THE WAR PRODUCTION BOARD”. COMPLETE WITH THE FOLLOWING. MACHINE HAS BEEN REPLACED BY A HARRISON M300 ENGINE LATHE. The item “COMPLETE SOUTHBEND LATHE 10 HARDENED WAYS, TAPER, CHUCKS, TOOLING, CABINET” is in […]
Clean Southbend Heavy Ten 10L Lathe 4 Bed with Tooling
Heavy 10 10L 10 throw lathe. With 3ph 2/4hp motor and all original Southbend motor conduit and switch (not photoed). Has the large bore through hole, photoed. 4 bed Comes with a 6 3-jaw Southbend chuck and some tooling. Located in a residential garage with backup truck/trailer access and a lift on site. The item […]
Complete Southbend Lathe 10 Hardened Ways, Taper, Chucks, Tooling, Cabinet
10” SWING, 24 BETWEEN CENTERS, 3 1/2′ BED LENGTH ON CABINET. CATALOG # CL187ZB, S/N 20292 R. COMPLETE WITH THE FOLLOWING. 6 1/2″ THREE JAW CHUCK W/ ID & OD JAWS, 6 1/2″ FOUR JAW CHUCK, 5C COLLET CHUCK. 9 1/4″ FACE PLATE, 7″ DRIVE PLATE. STEADY REST, THREAD DIAL, CHUCK COVER, ROCKER TOOL POST […]
Southbend 10L (heavy ten) lathe 4 ½ bed lots of tools included no reserve
This was my second heavy ten lathe and certanly a joy to run. The only thing you should need to start making chips is a phase converter. Here is a list of what comes with this package. South bend 10L (heavy ten). Lantern tool post with tool holder. Quick change tool post with Aloris AXA2 […]
Southbend Turn-Nado (Cat. CL170E) Tool Room Engine Lathe
You are looking at: 17″ x 60″ Southbend “Turn-Nado” Cat. CL170E Tool Room Engine Lathe. Capacity Swing Over Bed and Saddle Wings…………………………………. 17-1/8 Swing Over Cross Slide…………………………………………. 10-1/2 Distance between Centers…………………………………………… 60 Headstock Spindle Nose…………………………………………… 8 D-1 Cam-Lock Size of Center (Morse Taper)……………………………………… 5 Hole through Spindle…………………………………………… 3-5/32 Spindle Speeds 1800 – 900 RPM Motor […]
17 x 60 Southbend Turn-Nado (Cat. CL170E) Tool Room Engine Lathe
You are looking at: 17″ x 60″ Southbend “Turn-Nado” Cat. CL170E Tool Room Engine Lathe. Capacity Swing Over Bed and Saddle Wings…………………………………. 17-1/8 Swing Over Cross Slide…………………………………………. 10-1/2 Distance between Centers…………………………………………… 60 Headstock Spindle Nose…………………………………………… 8 D-1 Cam-Lock Size of Center (Morse Taper)……………………………………… 5 Hole through Spindle…………………………………………… 3-5/32 Spindle Speeds 1800 – 900 RPM Motor […]
Southbend lathe #C L 644 A, metal lathe, milling, tooling, nice lathe no reserve
Hi folks here is a nice bench top southbend lathe , it came from a shop that was using it to make small wood and plastic. Parts , it runs strong with minimal play , it is 110 volt with forward and reverse , the model number is C L 644 A. It has a […]